跳转到主内容

E 系列控制器上的默认管理端口 IP 地址是什么?

Views:
93
Visibility:
Public
Votes:
0
Category:
e-series-systems
Specialty:
esg
Last Updated:

可不使用  

适用于

E 系列

解答

每个控制器的默认管理端口 IP 地址如下所示。

管理端口  控制器 A 控制器 B
1 192.168.128.101 192.168.128.102
2 192.168.129.101 192.168.129.102

:默认 IP 地址的格式为 192.168.XXX.10Y 、其中:
xxx=128 是第一个端口、 129 是控制器上的第二个端口。
y =1 表示控制器 A 、 2 表示控制器 B

在控制器引导过程中,如果:

  • 以太网链路已打开 / 联机、并且有 DHCP 服务器(默认情况下控制器上已启用 DHCP )、 DHCP 服务器将根据 DHCP 服务器设置分配 IP 和子网掩码。
  • 以太网链路已打开 / 处于联机状态且没有 DHCP 服务器、将分配默认 IP 和子网掩码(在 DHCP 超时时间为 3 分钟后)—以下是默认的网络配置参数:
    Controller 1 (port 1):  IP Address : 192.168.128.101     Subnet Mask : 255.255.255.0
    Controller 1 (port 2):  IP Address : 192.168.129.101     Subnet Mask : 255.255.255.0
    Controller 2 (port 1):  IP Address : 192.168.128.102     Subnet Mask : 255.255.255.0
    Controller 2 (port 2):  IP Address : 192.168.129.102     Subnet Mask : 255.255.255.0
  • 以太网链路关闭、 IP 和子网掩码值显示“ 0.0.0.0 ”、netCfgShow表示未设置 IP 或子网掩码、而不是 IP 和子网掩码的值为“ 0.0.0.0 ”。这将在 netcfgshow 输出中显示、如以下示例所示:
    -> netCfgShow
    ==== CURRENT NETWORK CONFIGURATION ====

    My Host Name           :  Controller A

    Interface Name     if0 :  gei0

    MAC Address        if0 :  00:80:e5:1f:8f:00
    IP Address         if0 :  0.0.0.0

    Subnet Mask        if0 :  0.0.0.0

    Config Flags       if0 :  0x8F - IPV4_EN IPV6_EN AUTOCONF_EN

    NIC Speed/Duplex   if0 :  0x0000 - AUTO
    Interface Name     if1 :  gei1
    MAC Address        if1 :  00:80:e5:1f:8f:01
    IP Address         if1 :  0.0.0.0

    Subnet Mask        if1 :  0.0.0.0

    Config Flags       if1 :  0x8F - IPV4_EN IPV6_EN AUTOCONF_EN
    NIC Speed/Duplex   if1 :  0x0000 - AUTO

    Server Host Name       :  server

    Server IPv6 Address    :  ::

    Gateway IP Address     :  0.0.0.0

    Network Init Flags     :  0x80 - TELNET_EN

    User Name              : 

    User Password          : 

    '*' 表示动态分配或默认地址
    值 =58=0 x 3a=':'
  • 用户手动设置 IP 和子网掩码、上述所有行为都将被覆盖、分配的静态值将持续存在。

:在控制器固件 07.70.xx.xx 之前、控制器已预配置静态 IP/ 子网。如果网络配置问题持续存在,请联系技术支持代表以寻求帮助。

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.
Scan to view the article on your device