跳转到主内容

由于存储端SFP出现故障、在连接到Brocade交换机的光纤通道目标上检测到链路中断

Views:
21
Visibility:
Public
Votes:
0
Category:
ontap-9
Specialty:
SAN
Last Updated:

适用场景

  • ONTAP 9
  • FCP
  • Brocade交换机

问题描述

  • EMS Log on NetApp End报告 链路重置事件、 其中链路关闭并在 5秒内恢复。

Wed Feb 14 14:52:15 +0530 [NetApp1: fct_tpd_work_thread_0: scsitarget.slifct.linkBreak:error]: Link break detected on Fibre Channel target HBA 2c with event status 1 , topology type 1, status1 0x0, status2 0x0.
Wed Feb 14 14:52:20 +0530 [NetApp1: fct_tpd_work_thread_0: scsitarget.hwpfct.linkUp:notice]: Link up on Fibre Channel target adapter 2c.

Fibre Channel Target Adapter 2c
Received Optical Power - 996.9 (uWatts)
SFP Transmitted Optical Power - 992.0 (uWatts)

  • 在问题描述时间前后、存储端未报告任何其他FCP事件。
  • 某些场景、其中Tx位于较低范围:

JxA-NxAxF::> network fcp adapter show -fields sfp-tx-power
node        adapter sfp-tx-power
---------------- ------- --------------
JxA-NxAxFxx02   0e    177.7 (uWatts)

  • 连接的交换机端口未报告porterrshow 输出-

/fabos/cliexec/porterrshow :
      frames     enc    crc    crc    too    too    bad    enc   disc   link   loss   loss   frjt   fbsy    c3timeout    pcs    uncor
     tx     rx    in    err    g_eof   shrt   long   eof    out   c3    fail   sync   sig            tx    rx    err    err
75:  242.2k  398.3k   0     0     0     0     0     0     0     0     0     0     0     0     0     0     0     0     0

  • 交换机端口的状态为已启动且联机。

/fabos/bin/switchshow :
Index Slot Port Address Media  Speed     State   Proto
============================================================
75   9   11   654bxx  id   N32  Online   FC  F-Port  1 N Port + 1 NPIV public

  • Errdump 在问题描述时间内未报告任何此类错误事件。
  • Frame timeout detected 存储连接的交换机端口

2024/09/20-02:37:58, [AN-1014], 434931, FID 128, INFO, Jx_G720_x, Frame timeout detected, tx port 25 rx port 6, sid 3xx00, did 3xx02, timestamp 2024-09-20 02:37:58

  • Fabriclog 输出 显示了连接到受影响存储端口的交换机端口 遇到 重置。

Switch 0; Wed Feb 14 14:51:40 2024 IST (GMT+5:30)
14:51:40.025111 SCN Port Offline;rsn=0x2,g=0x6a        D0,P0  D0,P0  75   NA
14:51:40.025118 *Removing all nodes from port         D0,P0  D0,P0  75   NA
14:51:44.795477 SCN LR_PORT(0);g=0x6a             D0,P0  D0,P0  75   NA
14:51:44.858285 SCN Port Online; g=0x6a,isolated=0      D0,P0  D0,P1  75   NA
14:51:44.858365 Port Elp engaged               D0,P1  D0,P0  75   NA
14:51:44.858377 *Removing all nodes from port         D0,P0  D0,P0  75   NA
14:51:44.858608 SCN Port F_PORT                D0,P1  D0,P0  75   NA
14:51:44.968592 SCN LR_PORT(0);g=0x6a LR_IN          D0,P0  D0,P0  75   NA

  • 交换机端的SFP Tx电源看起来很好、这表明交换机SFP处于良好状态。
  •  交换机端的Tx功率(1238.9 uW)相比,Rx功率非常低(572.5uW)

=============
Slot  9/Port 11:
=============
RX Power:   -2.4   dBm (572.5uW)
TX Power:   0.9    dBm (1238.9 uW)

  • 而存储端Tx功率是SFP传输光功率- 992.0 (uWatt)
  • 这表明问题描述位于交换机上游的某个位置,可以是电缆或终端设备SFP (在本例中为NetApp存储)。
  • 需要执行电缆测试、以进一步隔离问题描述电缆是否出现故障。
  • 如果电缆正常、则必须交换连接到交换机的终端设备上的SFP。

 

 

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.