跳转到主内容

存储上的SFP功率低于建议值

Views:
104
Visibility:
Public
Votes:
0
Category:
fas-systems
Specialty:
SAN
Last Updated:

 

执行

适用场景

  • FAS/AFA系统
  • ONTAP 9
  • 光纤通道(FC) 

问题描述

  • FC链路中断、链路轻拍和/或FCP性能下降。
  • Sysconfig -a 将状态显示为link not connected""或link disconnected ""

    slot 0: Fibre Channel Target Host Adapter 0h
            (QLogic 8324 (8362) rev. 2, <LINK NOT CONNECTED>)
             Firmware rev:    8.9.0
             Flash rev:      4.1.0
             Host Port Addr:   000000
             Connection:     No link
             Switch Port:     Unknown   xxxx:41
                   SFP Vendor Name:   AVAGO
                   SFP Vendor P/N:   AFBR-57F5MZ-NA1
                   SFP Vendor Rev:   01
                    SFP Connector:    LC
                   SFP Capabilities:  4, 8, 16 Gbit/Sec

  • FCP-ADAPTER.XML 登录ASUP 会将 受影响端口的Rx/Tx值显示为0.0 uW。

    Rx : 0.0 (uWatts)
    Tx : 0.0 (uWatts)

  • 收到有关NetApp上的存储LIF的以下错误:
Service: Interface FCP XXX.FC_LIF State: CRITICAL Time: Wed Mar 15 15:16:13 CET 2023 Description: CRIT - State: online, 8 Gbit/s (wrong speed, expected 16 Gbit/s)(!!), Address x0:0a:09:84:80:74:xy:xx, Read: 1235654.27, Write: 9303298.57, Read OPS: 71, Write OPS: 138, Latency: 1.15 ms, Read Latency: 0.03 ms, Write Latency: 1.08ms
  • EMS 记录以下事件-
    Tue Feb 27 00:20:29 +0000 [netapp: fct_tpd_work_thread_0: scsitarget.fct.sfpTxPowerLow:alert]: The SFP in FC target adapter 0f reports that it is transmitting (TX) at a low level of power. Operating value 263 (uWatts), Threshold value 317 (uWatts).

 

  • network fcp adapter show 在ONTAP命令行界面上显示低TX功率:

Received Optical Power   570.7 (uWatts)
SPF Transmitted Optical Power   123.8 (uWatts)

  • Rx功率低表示问题描述上游连接到存储端口、即交换机端的缆线和SFP中的硬件有故障  这不是存储上的SFP的问题。
  • 低Tx功率表示存储端口上存在问题描述。
  • 以下值为近似值:

SFP版本

光值范围

短波2/4/8GB SFP接收功率范围

短波2/4/8GB SFP传输功率范围

-6 dBm (250 uWatt)到-2 dBm (630 uWatt)

-6 dBm (250 uWatt)到0 dBm (1000 uWatt)

短波4/8/16 Gb SFP接收功率范围

短波4/8/16 Gb SFP传输功率范围

-5.2 dBm (300 uWatt)到0 dBm (1000 uWatt)

-5.2 dBm (300 uWatt)到-1 dBm (790 uWatt)

短波8/16/32 Gb SFP接收功率范围

短波8/16/32 Gb SFP传输功率范围

-4.6 dBm (340 uWatt)到2 dBm (1580 uWatt)

-4.6 dBm (340 uWatt)到2 dBm (1580 uWatt)

  • 可能发生关联:
    • 增加交换机端口上的错误计数器
    • 主机操作系统出现IO故障和/或超时
    • 来自主机操作系统的一个或多个故障路径
    • 存储控制器上的FC目标端口处于<OFFLINE>或 <LINK NOT CONNECTED>状态
    • 链路重置/端口重置
    • 适配器发现挂起错误

 

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.