跳转到主内容

集群端口上发生大量CRC错误

Views:
67
Visibility:
Public
Votes:
0
Category:
fas-systems
Specialty:
hw
Last Updated:

适用场景

  • ONTAP 9
  • 无交换机集群

问题描述

  • CRC错误会在使用的集群端口上计数多次 ifconfig:

-- interface  e0b  (232 days, 2 hours, 21 minutes, 3 seconds) --

RECEIVE
 Total frames:    252m | Frames/second:    13  | Total bytes:    39644m
 Bytes/second:    1977  | Total errors:    1218  | Errors/minute:     0 
 Total discards:    0  | Discards/minute:    0  | Multi/broadcast:  1020k
 Non-primary u/c:    0  | CRC errors:     1212  | Runt frames:      0 
 Fragment:       0  | Long frames:      0  | Jabber:        3 
 Length errors:     3  | No buffer:       0  | Xon:          0 
 Xoff:         0  | Pause:         0  | Jumbo:       1293k
 Noproto:        0  | Error symbol:    236  | Illegal symbol:   199 
 Bus overruns:     0  | Queue drops:      0  | LRO segments:    249m
 LRO bytes:     26713m
| LRO6 segments:     0  | LRO6 bytes:      0 
 Bad UDP cksum:     0  | Bad UDP6 cksum:    0  | Bad TCP cksum:     0 
 Bad TCP6 cksum:    0  | Mcast v6 solicit:   0 
TRANSMIT
 Total frames:    561m | Frames/second:    28  | Total bytes: 139g
 Bytes/second:    6980  | Total errors:     0  | Errors/minute:     0 
 Total discards:    0  | Queue overflow:    0  | Multi/broadcast:  1031k
 Xon:          0  | Xoff:         0  | Pause:         0 
 Jumbo:       2565k | Cfg Up to Downs:    2  | TSO non-TCP drop:   0 
 Split hdr drop:    0  | Timeout:        0  | TSO segments:    402k
 TSO bytes:     4840m | TSO6 segments:     0  | TSO6 bytes:      0 
 HW UDP cksums:    154k | HW UDP6 cksums:    0  | HW TCP cksums:    556m
 HW TCP6 cksums:    0  | Mcast v6 solicit:   0 
DEVICE
 Mcast addresses:    3  | Rx MBuf Sz:     4096 
LINK INFO
 Speed:       10000M | Duplex:       full | Flowcontrol:     none
 Media state:    activ
e | Up to downs: 8

  • EMS错误消息每小时持续提供以下输出:

Tue Dec 01 04:04:26 JST [node 2: intr: netif.linkErrors:error]: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
Tue Dec 01 05:04:27 JST [node 2: intr: netif.linkErrors:error]: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
Tue Dec 01 06:04:27 JST [node 2: intr: netif.linkErrors:error]: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
Tue Dec 01 07:04:27 JST [node 2: intr: netif.linkErrors:error]: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
Tue Dec 01 08:04:28 JST [node 2: intr: netif.linkErrors:error]: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
Tue Dec 01 09:04:29 JST [node 2: intr: netif.linkErrors:error]: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.

  • 即使单独更换HA配对控制器e0b端口之间的缆线、上述错误消息也不会停止。

::> event log show
Time         Node Severity    Event
------------------- ---------------- ------------- ---------------------------
1/5/2021 15:11:21 node 2   ERROR      netif.linkErrors: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicat
e a duplex mismatch.
1/5/2021 14:54:52   node 1   EMERGENCY    vifmgr.clus.linkdown: The cluster port e0b on node node 1 has gone down unexpectedly.
1/5/2021 14:54:52   node 2   EMERGENCY    vifmgr.clus.linkdown: The cluster port e0b on node node 2 has gone down unexpectedly.
1/5/2021 14:11:20   node 2   ERROR      netif.linkErrors: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
1/5/2021 13:11:20   node 2   ERROR netif.linkErrors: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port, or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
1/5/2021 12:11:19   node 2   ERROR      netif.linkErrors: Excessive link errors on network interface e0b. Might indicate a bad cable, switch port,
 or NIC, or that a cable connector is not fully inserted in a socket. On a 10/100 port, might indicate a duplex mismatch.
Press <space> to page down, <return> for next line, or 'q' to quit... q
6 entries were displayed.

 

  • 这是一种无交换机集群配置、目标e0b端口是将节点1 e0b作为集群LIF端口直接连接到节点2 e0b的端口。
  • 更换缆线后、CRC错误计数继续增加、错误继续报告
  • 连接到速度和双工的每个节点之间的端口没有差别、也不使用SFP等收发器。
  • 交叉连接显示错误仍与端口有关、请勿随缆线一起出现。

 

 

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.