跳转到主内容

FCP目标适配器显示链路已断开

Views:
123
Visibility:
Public
Votes:
1
Category:
ontap-9
Specialty:
san
Last Updated:

适用场景

  • ONTAP 9
  • FCP

问题描述

  • 事件日志条目表示FC链路已断开连接:

5/23/2020 21:11:31  cluster-node1  ERROR scsitarget.ispfct.linkBreak: Link break detected on Fibre Channel target adapter 1b. Firmware status code status1 0x2, status2 0x7, and status4 0x0.

 

  • sysconfg -a 将端口状态报告为Link Disconnected""
slot 1: Fibre Channel Target Host Adapter 1b (QLogic 8324 (8362) rev. 2, <LINK DISCONNECTED>) Board Name: QLE2672 Serial Number: RFE2005W04482 Firmware rev: 8.9.0 Flash rev: 1.1.2 Host Port Addr: 000000 FC Nodename: xx:0a:09:80:80:xx:xy:xx (500a098080b3a125) FC Portname: xx:0a:09:82:80:xy:yy:xx (500a098280b3a125) Connection: No link Switch Port: Unknown SFP Vendor Name: FINISAR CORP. SFP Vendor P/N: FTLF8529P4BCV-QM SFP Vendor Rev: B SFP Serial No.: P2SABCS SFP Connector: LC

 

  • Network fcp adapter show 在命令行界面上执行的命令会将运行状态报告为"link disconnected"

cluster::> network fcp adapter show
           Connection  Port    Admin   Operational
Node      Adapter Established Address   Status  Status
------------ ------- ----------- --------- ------- -----------------------
cluster-node1
       0c    false     0      up    link not connected
cluster-node1
       0d    false     0      up    link not connected
cluster-node1
       1a      true     f0500    up    online
cluster-node1
       1b    true     0      up    link disconnected
cluster-node2
       0c    false     0      up    link not connected
cluster-node2
       0d    false     0      up    link not connected
cluster-node2
       1a    true     f0600    up      online
cluster-node2
       1b    true     f0600    up    online

 

  • 存储HBA端口仍以物理方式连接

 

尝试隔离问题描述的以下故障诊断步骤:

  • 已 使用以下命令验证远程SFP的运行状况并已退回端口:

Cisco示例:

switch# config terminal
switch(config)# interface fc <slot>/<port#>
switch(config)# show int fc <slot>/<port#> transceiver detail
switch(config-if)# shutdown
switch(config-if)# no shutdown

Brocade示例:

switch:admin> sfpshow <index # OR slot/port #>
switch:admin> portdisable <index # OR slot/port #>
switch:admin> portenable <index # OR slot/port #>

  • 已执行物理检查并重新安装连杆和 配线板部件。
  • 重新安装后、重复端口弹跳过程。
  • 更换/交换两端的组件、包括缆线和SFP。

 

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.