跳转到主内容

ONTAP AFF 和 FAS 型号的正常关闭和启动步骤是什么?

Views:
135
Visibility:
Public
Votes:
1
Category:
ontap-9
Specialty:
hw
Last Updated:

适用于

  • Data ONTAP 7 及更早版本
  • 集群模式 Data ONTAP 8
  • Data ONTAP 8 7-模式
  • ONTAP 9

解答

在电源循环过程中、按什么顺序打开和关闭元件电源?

最佳实践

  • 确保备份已完成
  • 确保完成 SnapMirror 更新
  • 要防止自动生成支持案例,请发送一条 AutoSupport 消息以指示正在进行维护。
    • 发出以下命令: system node autosupport invoke -node * -type all -message MAINT=maintenance-window-in-hours
    • maintenance-window-in-hours 指定维护时段的长度,最长为 72 小时。

在 Data ONTAP 7- 模式中执行以下步骤以关闭系统:

如果存储系统是集群模式的,请输入 cf disable 。或者,请按照下面步骤 4 中给出的“针对集群存储系统 ... ”一节进行操作。

  1. 通知、断开连接并在需要时关闭所有连接的 CIFS/NFS 客户端。
  2. 如果有任何主机具有 FCP 或基于 iSCSI 的 LUN 、请在关闭存储系统之前将其关闭。
  3. 使用cifs terminate命令终止 CIFS 。
  4. halt存储系统命令行界面上运行命令。允许存储系统终止 Data ONTAP 、然后进入“确定”、“ CFS ”或“加载程序”提示符。
    对于集群模式存储系统,如果未运行 cf disable,请 halt -f -t 在每个配对系统上运行命令。
  5. 根据需要关闭磁头和所有连接的磁盘架的电源。
  6. 从存储系统和磁盘架背面的电源设备上拔下电缆,以避免在恢复外部电源时出现任何电气问题。

在集群模式 Data ONTAP 中执行以下步骤以关闭系统:

  1. 通知、断开连接并在需要时关闭所有连接的 CIFS/NFS 客户端。
  2. 如果有任何主机具有 FCP 或基于 iSCSI 的 LUN 、请在关闭存储系统之前将其关闭。
  3. 登录到所有节点、一次登录一个节点(最好使用串行控制台或 RLM/SP )并运行:
    halt -node local -inhibit-takeover true -skip-lif-migration true

    运行halt上述命令后将显示以下信息。在系统提示您是否要继续时键入 " y " :
    system node halt

    Warning: Rebooting or halting node "node-01" in an HA enabled cluster
         with takeover inhibited may result in a data serving failure and
         client disruption. To ensure continuity of service, do the following
         before rebooting or halting the node: Disable cluster HA using the
         command: "cluster ha modify -configured false".
         To transfer epsilon to the partner node, use the following commands
         (privilege:advanced):
             cluster modify -epsilon false -node <local-node>
             cluster modify -epsilon true -node <partner-node>
    Do you want to continue? {y|n}: y


    每个节点可能需要几分钟的时间才能关闭。然后,每个节点都应重置并返回LOADER>到提示符。如果没有控制台或 RLM/SP 访问权限、请运行 System Node show 命令、在停止最终节点之前确认整个节点停机状态。在最后一个节点停止后、您可以安全地关闭所有组件。
  4. 根据需要关闭磁头和所有连接的磁盘架的电源。
  5. 从存储系统和磁盘架背面的电源设备上拔下电缆,以避免在恢复外部电源时出现任何电气问题。

执行以下步骤使系统重新联机:

  1. 如果先前已断开连接,请重新连接所有电源电缆。
  2. 启动核心交换机,否则集群将无法正常工作。
  3. 首先对所有磁盘架进行物理开机。等到最后一个磁盘架打开 30 秒后、打开存储系统头电源、以便在 Data ONTAP 要求所有磁盘时都可用。
  4. 验证存储系统是否已启动、所有服务均在运行、以及是否存在网络连接。
  5. 对于 7 模式 HA 对、如果使用禁用了集群cf disable、请输入并cf enable监控。 cf status.
  6. 对于集群 ONTAP 系统、请选中集群显示和存储故障转移显示以确认 CFO/CO 已配置 / 启用。

 

  • 如果在该时间过后完成维护,您可以调用一条 AutoSupport 消息,指示维护期结束: system node autosupport invoke -node * -type all -message MAINT=end 

 

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.