跳转到主内容

重新启动后,连接到 Cisco 交换机的以太网端口不会立即联机

Views:
15
Visibility:
Public
Votes:
0
Category:
aff-series<a>2008976876</a>
Specialty:
hw
Last Updated:

适用场景

  • AFF-A400
  • FAS8300
  • ONTAP 9
  • Cisco Nexus 9000系列交换机

问题描述

  • 端口 e0e 到 e0h 的链路启动延迟发生在重新启动后。
  • 在端口 e0e 到 e0h 之间随机显示问题描述。

         slot 0: 10G/25G Ethernet Controller CX5-Mezz
                        e0e MAC Address:    XX:XX:XX:XX:XX:XX (auto-10g_sr-fd-up)
                            SFP Vendor:         FINISAR CORP.
                            SFP Part Number:    FTLX8574D3BCL
                            SFP Serial Number:  XXXXXXX
                        e0f MAC Address:    XX:XX:XX:XX:XX:XX (auto-unknown-fd-down)
                            SFP Vendor:         FINISAR CORP.
                            SFP Part Number:    FTLX8574D3BCL
                            SFP Serial Number:  XXXXXXX
                        Device Type:        CX5 PSID(NAP0000000007)
                        Firmware Version:   16.26.4012
            slot 0: 10G/25G Ethernet Controller CX5-Mezz
                        e0g MAC Address:    XX:XX:XX:XX:XX:XX (auto-10g_sr-fd-up)
                            SFP Vendor:         FINISAR CORP.
                            SFP Part Number:    FTLX8574D3BCL
                            SFP Serial Number:  XXXXXXX
                        e0h MAC Address:    XX:XX:XX:XX:XX:XX (auto-unknown-fd-down)
                            SFP Vendor:         FINISAR CORP.
                            SFP Part Number:    FTLX8574D3BCL
                            SFP Serial Number:  XXXXXXX
                        Device Type:        CX5 PSID(NAP0000000007)
                        Firmware Version:   16.26.4012

  • 重新拔插缆线后,端口可以启动。
  • Cisco 交换机上使用 10G SR SFP 。

        show int transceiver detail 在 Cisco 日志上:

Ethernet1/1
    transceiver is present
    type is 10Gbase-SR
    name is CISCO-ACCELINK
    part number is RTXM228-551-C98
    revision is 1.0
    serial number is XXXXXXXXXXX
    nominal bitrate is 10300 MBit/sec
    Link length supported for 50/125um OM2 fiber is 82 m
    Link length supported for 62.5/125um fiber is 26 m
    Link length supported for 50/125um OM3 fiber is 300 m
    cisco id is 3
    cisco extended id number is 4
    cisco part number is 10-2415-03
    cisco product id is SFP-10G-SR
    cisco version id is V03

 

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.