跳转到主内容

由于集群端口已关闭,节点无法访问

Views:
7
Visibility:
Public
Votes:
0
Category:
fabric-interconnect-and-management-switches
Specialty:
hw
Last Updated:

适用场景

  • FAS2720
  • ONTAP 9.7P7
  • BES-53248 集群网络交换机。

问题描述

  • 可通过 storage failover show 命令查看节点
 Cluster::> storage failover show Takeover Node Partner Possible State Description -------------- -------------- -------- ------------------------------------- node-01 node-02 true Connected to node-02 node-02 node-01 true Connected to node-01 node-03 node-04 true Connected to node-04 node-04 node-03 true Connected to node-03
  • 节点显示为无法通过 node show 命令访问 
 Cluster::> node show Node Health Eligibility Uptime Model Owner Location --------- ------ ----------- ------------- ----------- -------- --------------- node-01 true true 128 days 00:59 AFF-A220 London node-02 true true 128 days 00:59 AFF-A220 London node-03 true true 128 days 00:21 FAS2720 London node-04 true true - - - - 4 entries were displayed.
  • 根据正常运行时间,节点正在运行
 Cluster::> node run -node * -c "uptime" 4 entries were acted on. Node: node-01 2:32pm up 131 days, 2:30 14786852056 NFS ops, 3892 CIFS ops, 0 HTTP ops, 0 FCP ops, 0 iSCSI ops, 0 NVMF ops Node: node-02 2:32pm up 131 days, 2:30 20465055899 NFS ops, 3884 CIFS ops, 0 HTTP ops, 0 FCP ops, 0 iSCSI ops, 0 NVMF ops Node: node-03 2:32pm up 131 days, 1:52 981629257 NFS ops, 5809919861 CIFS ops, 0 HTTP ops, 0 FCP ops, 3209009366 iSCSI ops, 0 NVMF ops Node: node-04 2:32pm up 131 days, 1:52 7395009429 NFS ops, 4593427421 CIFS ops, 0 HTTP ops, 0 FCP ops, 0 iSCSI ops, 0 NVMF ops
  • 集群网络端口报告为已关闭
 slot 0: 10 Gigabit Ethernet Controller IX5-SFP+ e0a MAC Address: XX:XX:XX:XX:XX:XX (auto-unknown-fd-down) SFP Vendor: Molex Inc. SFP Part Number: 747529720 SFP Serial Number: XXXXXXXXX 
  • 报告连接到这些端口的集群网络交换机缺失
节点 节点 -02
监控 (集群交换机)
Alert ID ClusterSwitchMissing 警报
警报资源 交换机 -01
子系统 交换机运行状况
指示时间 2021 年 6 月 26 日星期六 13 : 42 : 57
感知的严重性 重大
可能原因: 配置错误
问题描述 集群交换机缺少冗余配置。
  • 目测检查交换机时,任何集群端口上均未显示任何 LED 活动
  • 通过串行连接到交换机时,所有集群端口均显示为已禁用
 (switch-01) #show port all Admin Physical Physical Link Link LACP Actor Intf Type Mode Mode Status Status Trap Mode Timeout --------- ------ --------- ---------- ---------- ------ ------- ------ -------- 0/1 Disable 10G Full Down Enable Enable long 0/2 Disable 10G Full Down Enable Enable long 0/3 Disable 10G Full Down Enable Enable long 0/4 Disable 10G Full Down Enable Enable long

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.