跳转到主内容

在ESXi 7.0中部署NetApp ONTAP FC-NVMe有哪些要求?

Views:
93
Visibility:
Public
Votes:
0
Category:
data-ontap-8
Specialty:
virt
Last Updated:

适用场景

  • ESXi 7.0 FC-NVMe
  • VMware vSphere 7.0
  • ONTAP

问题解答

VMware vSphere 7.0版本支持FC-NVMe存储堆栈。

此知识库文章 介绍了 提高ONTAP与 ESXi 7.0 FC-NVMe的互操作性所需的设置。

  1. 对于Broadcom Emulex LPe3200 x FCP HBA、必须设置以下参数以检测NVMe命名时间:

    esxcli system module parameters set -m lpfc -p lpfc_enable_fc4_type=3

    重新启动系统以使设置生效。

     注: Broadcom LPe3500x HBA不需要上述命令。

  1. 在ESXi 7.0检测到命名空间并从ONTAP提供新子系统后、ESXi 7.0不会检测到提供的新命名空间。要检测新子系统和命名空间、可以执行以下操作: 
     
    1. 在主机上执行重新扫描
  2. 要提高互操作性、必须将以下参数设置为"0":

    esxcfg-advcfg -s 0 /Misc/HppManageDegradedPaths

    注意: 如果未将此值设置为"0"、则会导致发生原因应用程序中断
     
    1. 重新启动系统。
    2. 检查是否已禁用配置、然后启动测试:

      esxcfg-advcfg -g /Misc/HppManageDegradedPaths

      上述命令应将值显示为0 ->“Value of HppManageDegradedPaths is 0”
       
  3. 要在命名空间上部署Solaris VM及其数据磁盘、请确保仅使用虚拟SCSI控制器(LSI Logic SAS、PVSCSI)。建议不要将虚拟NVMe控制器用于Solaris VM。
  4. NetApp支持FC SCSI LUN和命名空间共存配置。请参见VMware文档、了解VMware建议的LUN和命名器数量以及路径数。
  5. 对于部署在SCSI和NVMe命名空间上且虚拟SCSI控制器(LSI Logic SAS、PVSCSI)连接到该VM的VM、建议的磁盘超时时间为60秒。有关如何将磁盘超时设置为60秒的信息、请咨询相应的VM操作系统供应商。
  6. [1]有关任何待解决问题和BURT、请参见NetApp IMT。

追加信息

  • vSphere升级中心
  • HBA上的参数设置只需设置一次、如果添加了新HBA、则需要在新HBA上设置参数

 

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.