跳转到主内容

ONTAP重新启动后、XL710 40GbE端口上出现CRC错误

Views:
15
Visibility:
Public
Votes:
0
Category:
ontap-9
Specialty:
core<a>2009065366</a>
Last Updated:

适用场景

  • ONTAP 9
  • 10/40千兆以太网控制器XL710网络端口
    • X91440A以太网模块
    • X1144A以太网NIC (PCIe)
    • AFF A700s板载以太网端口
  • 前端40G交换机、如Cisco Nexus或类似产品

问题描述

  • 存储系统将10/40千兆位以太网控制器XL710网络端口连接到40G交换机(例如Cisco Nexus 9336C)
  • 在ONTAP重新启动或升级后、具有基于XL710的40 Gb以太网集群端口的节点会报告集群 网络降级 事件。示例
[node1: vifmgr: callhome.clus.net.degraded:alert]: Call home for CLUSTER NETWORK DEGRADED: CRC Errors Detected - High CRC errors detected on port e8a node node1
[node1: vifmgr: vifmgr.cluscheck.hwerrors:alert]: Port e8a on node node1 is reporting a high number (at least 1 per 1000 packets) of observed hardware errors (CRC, length, alignment, dropped).
  • 40GbE端口(用于集群或前端数据)在 ifstat 命令的Receive部分报告CRC错误。示例: 

::>system node run -node <node_name> -command ifstat e8a
-- interface e8a (0 hours, 5 minutes, 31 seconds) --
RECEIVE
Total frames: 23634 | Frames/second: 71 | Total bytes: 2019k
Bytes/second: 6100 | Total errors: 18292 | Errors/minute: 3316
Total discards: 0 | Discards/minute: 0 | Multi/broadcast: 92
Non-primary u/c: 0 | CRC errors: 16978 | Runt frames: 0
Fragment: 0 | Long frames: 0 | Jabber: 1
Length errors: 0 | No buffer: 0 | Xon: 0
Xoff: 0 | Pause: 0 | Jumbo: 0
Noproto: 0 | Error symbol: 0 | Illegal symbol: 1313
Bus overruns: 0 | Queue drops: 0 | LRO segments: 20456
LRO bytes: 1707k | LRO6 segments: 0 | LRO6 bytes: 0
Bad UDP cksum: 0 | Bad UDP6 cksum: 0 | Bad TCP cksum: 0
Bad TCP6 cksum: 0 | Mcast v6 solicit: 0 | Lagg errors: 0
Lacp errors: 0 | Lacp PDU errors: 0

几小时/几天之后

-- interface e8a (4 days, 3 hours, 24 minutes, 3 seconds) --
RECEIVE
Total frames: 19227k | Frames/second: 54 | Total bytes: 2006m
Bytes/second: 5607 | Total errors: 19949k | Errors/minute: 3345
Total discards: 0 | Discards/minute: 0 | Multi/broadcast: 64901
Non-primary u/c: 0 | CRC errors: 18677k | Runt frames: 0
Fragment: 0 | Long frames: 0 | Jabber: 250
Length errors: 0 | No buffer: 0 | Xon: 0
Xoff: 0 | Pause: 0 | Jumbo: 0
Noproto: 0 | Error symbol: 0 | Illegal symbol: 1271k
Bus overruns: 0 | Queue drops: 0 | LRO segments: 17554k
LRO bytes: 1805m | LRO6 segments: 0 | LRO6 bytes: 0
Bad UDP cksum: 0 | Bad UDP6 cksum: 0 | Bad TCP cksum: 0
Bad TCP6 cksum: 0 | Mcast v6 solicit: 0 | Lagg errors: 0
Lacp errors: 0 | Lacp PDU errors: 0

  • 40GbE端口链路可能会闪烁或随后关闭。

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.